Industrial Water Cooling System Design Guide 2026: Closed-Loop vs Once-Through Cooling Systems for Plastic Manufacturing and Process Cooling
Industrial water cooling systems are the backbone of temperature control for plastics manufacturing, metalworking, HVAC, power generation, and countless other process cooling applications. The design decisions made at the planning stage — closed-loop versus once-through, cooling tower versus dry cooler, centralized versus distributed — have consequences that persist for the 15-25 year operational life of the system. Getting the design right means reliable operation, manageable operating costs, and a system that serves the facility's needs as production evolves. Getting it wrong means chronic performance problems, excessive water and energy costs, and expensive retrofit work.
This guide provides a comprehensive framework for designing industrial water cooling systems. It covers the two principal system architectures, the key components, the sizing methodology, and the decision criteria that determine which configuration is correct for your specific application and site conditions.
In a closed-loop cooling system, the process heat load and the atmospheric heat rejection are separated by a heat exchanger. The process equipment (mold temperature controllers, hydraulic oil coolers, machine tool cutting fluid systems, injection molding barrel cooling jackets, extruder barrel cooling zones) circulates water in a closed circuit through a plate-frame or shell-and-tube heat exchanger. A separate cooling water circuit — fed by a cooling tower or dry cooler — circulates cooling water through the other side of the heat exchanger, removing the heat from the process circuit and rejecting it to the atmosphere.
The key characteristic of a closed-loop system is that the process water circuit is sealed from the atmosphere — the same water circulates continuously in the process circuit, gaining heat from the process and losing it at the heat exchanger, with no evaporation or consumption of process water. This means:
In a once-through cooling system, raw water from the municipal supply (or from a borehole, river, or cooling water main) is passed through the process equipment directly, absorbs heat, and is discharged to drain. There is no recirculation — each unit of cooling water is used once and discarded.
The key characteristic is simplicity: no heat exchanger, no cooling tower, no recirculating pump circuit — just a supply line, the process equipment, and a drain. This makes once-through systems very simple to install and commission. However, the ongoing water consumption and the thermal pollution implications mean that once-through cooling is restricted or prohibited by regulation in most industrialized regions for all but the smallest heat loads. Even where permitted, the operating cost of once-through cooling — in water and in wastewater charges — makes it uneconomical for anything other than very small or intermittent heat loads.
For any industrial facility with a sustained process cooling load — a plastics manufacturing plant, a metalworking shop, a data center — closed-loop cooling is the standard choice for three fundamental reasons:
The heat rejection component is the critical element of the atmospheric side of a closed-loop cooling system. The choice is between an evaporative cooling tower and a dry cooler (also called a closed-circuit cooling tower):
Cooling tower: Evaporative heat rejection — the cooling water is sprayed over fill media while ambient air is drawn or forced across it. Evaporation of a small fraction of the circulating water (approximately 1-2% of circulation rate per 6-8 degrees Celsius of temperature drop) removes heat very efficiently, allowing the cooling water to be cooled to within 3-5 degrees Celsius of the ambient wet bulb temperature. This makes cooling towers the most efficient heat rejection technology for hot climates and high-density heat loads. The trade-off is water consumption (evaporative loss) and the need for ongoing water treatment to prevent scale, corrosion, and biological growth in the tower basin and circulating water circuit.
Dry cooler: Sensible heat rejection only — the cooling water circulates through a fin-and-tube heat exchanger with ambient air blown across it by fans. No evaporation occurs, so there is no water consumption (other than very small losses from leakage). Dry coolers are suitable for climates where the ambient dry bulb temperature rarely exceeds 35-40 degrees Celsius, or where water availability or regulations make evaporative cooling impractical. They require significantly more airflow than a cooling tower for equivalent heat rejection, which makes them physically larger and noisier than equivalent-capacity cooling towers.
The heat exchanger separates the process water circuit from the cooling water circuit. The choice of heat exchanger type depends on the heat load, the required approach temperature, and the water quality on each side of the circuit:
Plate-frame heat exchangers use thin corrugated metal plates to create a large surface area in a compact footprint. They offer very low approach temperatures (as little as 1-2 degrees Celsius) and high heat transfer efficiency. They require clean water on both sides — suspended solids or fibers in either circuit will quickly block the narrow flow channels between plates. They are the preferred choice for most closed-loop industrial cooling systems where water quality can be controlled.
Shell-and-tube heat exchangers are more tolerant of suspended solids and debris in the cooling water circuit. They are the standard choice where the cooling water circuit is fed from a raw water source (borehole, river, cooling water main) that may contain suspended solids, or where the process water circuit may contain oil or other contaminants. They require more floor space and have higher approach temperatures (typically 3-5 degrees Celsius) than plate-frame units.
The process water circulation pump must deliver the required flow rate against the pressure drop of the entire process circuit — including the heat exchanger, all connecting piping, and the process equipment itself. Pump selection is typically the most commonly underestimated element of a cooling system design. The pump must be sized for the worst-case pressure drop: the combined resistance of the heat exchanger at rated flow, the longest pipe run, and the highest-pressure-drop piece of process equipment on the circuit.
Piping design should minimize pressure losses: use the largest practical pipe diameter (the pump energy cost over the 15-20 year life of the system will far exceed the pipe cost premium of using a larger pipe size), minimize the number of fittings and bends, and use long-radius elbows rather than short-radius mitered bends.
The process water circuit must have an expansion tank to accommodate the increase in water volume as temperature rises from ambient to operating temperature. Without an expansion tank, the increased pressure in the sealed circuit will rupture pipework or damage equipment. The expansion tank should be positioned at the highest point in the circuit and connected to the system through an automatic air separator that bleeds any entrained air from the circulating water.
The total heat load is the sum of the heat generation from all process equipment on the cooling system:
The cooling water supply temperature to the process determines the approach temperature available at the process side of the heat exchanger. For most plastics processing applications, a cooling water supply temperature of 25-30 degrees Celsius is the target. For some precision applications, supply temperatures as low as 15-18 degrees Celsius may be required.
The actual achievable supply temperature depends on the ambient wet bulb temperature (for cooling towers) or dry bulb temperature (for dry coolers) and the design of the heat rejection system. As a rule of thumb:
Once the heat load and the required temperature rise across the cooling water circuit are known, the required flow rate is:
Flow rate (liters per second) = Heat load (kW) / (4.18 kJ per kg per K x temperature rise in K)
For example: a facility with a total heat load of 500 kW, using a cooling tower that achieves a 6-degree-Celsius temperature rise across the tower (inlet at 35 degrees Celsius, outlet at 29 degrees Celsius):
Flow rate = 500 / (4.18 x 6) = 500 / 25.08 = approximately 20 liters per second (72 m3 per hour)
The cooling tower or dry cooler must be sized to reject the total heat load at the design ambient conditions. For cooling towers, the critical parameter is the ambient wet bulb temperature — not the dry bulb. A cooling tower rated for 30 degrees Celsius wet bulb is fundamentally different from one rated for 27 degrees Celsius wet bulb, and the difference in performance at any given ambient condition is substantial.
For dry coolers, the critical parameter is the ambient dry bulb temperature and the required leaving water temperature. Dry cooler performance degrades rapidly as the ambient temperature rises — at 40 degrees Celsius ambient, a dry cooler designed for 35-degree-Celsius leaving water temperature may struggle to achieve 38-40 degrees Celsius.
| Factor | Closed-Loop System | Once-Through System |
|---|---|---|
| Water Consumption | Very low — only evaporation loss at tower (1-2% of circulation rate) | Very high — full flow rate continuously |
| Water Cost | Low — makeup water cost only for tower evaporation | High — full flow rate at water + wastewater tariffs |
| Process Water Quality | Fully controllable — demineralized, treated | Uncontrollable — depends on municipal supply |
| Regulatory Status | Generally acceptable everywhere | Prohibited or severely restricted in most regions |
| Heat Rejection Efficiency | High — cooling tower achieves close approach to wet bulb | Highest theoretically — but limited by water supply temperature |
| Capital Cost | Higher — requires tower, heat exchanger, pumps, piping | Lowest — supply + drain + process connections only |
| Operating Cost | Low — water, energy, water treatment | High — water + wastewater costs dominate |
| Maintenance | Medium — tower water treatment, pump servicing, periodic cleaning | Low — minimal equipment to maintain |
| Best For | All sustained industrial heat loads above 50-100 kW | Small intermittent loads, emergency backup, areas with unlimited water supply |
ZILLION ZL-WC series water cooled chillers provide precision process cooling for closed-loop industrial cooling applications. The chiller cools the process water circuit to the required supply temperature regardless of ambient conditions, providing consistent cooling capacity even in the hottest climates:
| Model | Cooling Capacity | Compressor | EER | Application |
|---|---|---|---|---|
| ZL-WC 050 | 50 kW | Screw | 4.5 | Small injection molding, laboratory cooling |
| ZL-WC 100 | 100 kW | Screw | 4.8 | Medium injection molding, packaging machinery |
| ZL-WC 200 | 200 kW | Screw | 5.0 | Large injection molding, blow molding |
| ZL-WC 350 | 350 kW | Screw | 5.2 | Industrial extrusion, large-scale manufacturing |
| ZL-WC 500 | 500 kW | Screw | 5.5 | Major industrial facilities, continuous process lines |
ZILLION industrial cooling towers provide efficient evaporative heat rejection for closed-loop industrial cooling systems. The cross-flow induced draft design achieves reliable performance in ambient temperatures up to 45 degrees Celsius:
| Model | Flow Rate (m3/hr) | Fan Power (kW) | Weight (kg) | Capacity Range |
|---|---|---|---|---|
| ZL-10T | 7.81 | 0.37 | 46 | Small systems, single machines |
| ZL-50T | 39.2 | 1.5 | 190 | Medium injection molding cells |
| ZL-100T | 78.1 | 2.2 | 500 | Large injection molding cells |
| ZL-200T | 156.2 | 4 | 880 | Industrial cells, multiple machines |
| ZL-300T | 234 | 7.5 | 1760 | Central plant, large facilities |
| ZL-500T | 392.4 | 7.5 | 2900 | Major industrial central systems |
Cooling tower water requires ongoing treatment to prevent four problems:
The sealed process water circuit in a closed-loop system requires much less active treatment than the cooling tower circuit, but should still be monitored:
A complete cooling system design should document:
The performance, reliability, and operating cost of an industrial cooling system are largely determined at the design stage. A system that is correctly sized for the actual heat load, designed for the correct ambient conditions, and specified with appropriate materials and water treatment will operate reliably for 15-25 years with routine maintenance. A system that is undersized, designed for incorrect ambient conditions, or specified with marginal equipment will underperform from day one — and will be expensive to fix.
The most common design errors — undersizing the heat exchanger, underestimating the process circuit pressure drop, selecting a cooling tower for the wrong wet bulb temperature, or specifying pipe sizes that are too small — are all preventable with proper survey work and calculation at the design stage. Invest the time in a thorough design, and the system will serve the facility well for its entire operational life.
For ZILLION cooling system products — water cooled chillers, cooling towers, and integrated systems — contact the ZILLION engineering team for system sizing and configuration recommendations.
Our company's series of products are well-known in the plastic auxiliary machinery industry for their excellent performance and high cost performance.
IPv6 network supported
English 
English
español
العربية
